Time and cost study on cold-formed steel and reinforced concrete construction - a comparison

Time and cost study on cold-formed steel and reinforced concrete construction - a comparison

Nowadays, the usage of cold-formed steel is quite common in some developed countries especially in building construction. However, in Malaysia, cold-formed steel construction is still considered as a new construction method. In local construction industry, cold-formed steel is only commonly seen in...

Saved in:

书目详细资料
主要作者:	Hu, Wei Kiet
格式:	Thesis
语言:	English
出版:	2008
主题:	TS Manufactures
在线阅读:	http://ir.unimas.my/id/eprint/596/1/Hu%20Wei.pdf
标签:	添加标签没有标签, 成为第一个标记此记录!

相似书籍

Flexural effect of flange width variation of ferrocement-cold-formed steel section as a composite beam
由: Hussain, Ali Saleh Hussain
出版: (2014)

A comparative study of activitybased costing (abc) and time-driven activity-based costing (tdabc) on cost accounting
由: Nurul Farahin, Zamrud
出版: (2021)

Asset management life cycle costing model for steel manufacturing industry in Saudi Arabia
由: Mohamed, Mohamed Ibrahim Elnaeim
出版: (2021)

The application of using time-driven activity-based costing in product operation and service operation
由: Sri Nur Areena, Mohd Zaini
出版: (2021)

Optimisation of the squeeze forming process
由: Ahmad, Rosli
出版: (2006)

Hierarchical Production Planning, Framework For The Batch Production Environment With Setup Time And Setup Cost Restrictions
由: Teo , Siew Chein
出版: (2005)

A case study in electrical & electronic industry using mahalanobis-taguchi system and time-driven activity-based costing on production environment
由: Nik Nurharyantie, Nik Mohd Kamil
出版: (2021)

High speed electroplating of nickel over stainless steel
由: Abdolahi, Ahmad
出版: (2010)

Mechanics of L-bending process for dual phase steel sheets
由: Boroujeni, Sahar
出版: (2013)

Formability of chromate conversion coating on zinc electroplated steel components
由: Ab. Hamid, Noor Hisham
出版: (1998)

Effects of heat treatment on the microstructures and electrochemical behavior of stainless steel
由: Haslan, Nur Hasmisha
出版: (2013)

Modeling of warranty cost for a lifetime warranty policy
由: Khoshbakht, Pezhman Ahmadi
出版: (2013)

Expected life cycle cost for systems with repairable components
由: Ebrahimi, Amirhossein
出版: (2013)

An inventory model for deteriorating items with nonlinear holding cost
由: Kamrani, Mohsen
出版: (2014)

Fabrication Of Cold Spray Ti-O Coatings Engineered From Agglomerated Powders
由: Abd. Rahim, Toibah
出版: (2016)

Performance of steel slag for wearing course compared with conventional wearing course
由: Shokri, Manouchehr
出版: (2014)

The effect of substrate temperature of (Ti,A1)N coating on AISI 304L stainless steel and high speed steel using physical vapor deposition (PVD) method
由: Choo, Shyh Jing
出版: (2013)

Processing And Tribological Characterization Of Kenaf Fibre Reinforced Polyurethane Composite
由: Singh, Narish
出版: (2011)

Thermal fatigue of laser modified tool steels mould surface at high temperature
由: Annie, Lau Sheng
出版: (2020)

Evaluation of hole quality on micro drilling AISI 304 austenitic stainless steel
由: Widodo, Widodo
出版: (2015)

A Case Study: Strategies For Reducing Production Cycle Time
由: Tse, Ngu Ik
出版: (2009)

Betelnut Fibers As Bio-Reinforcements In Polyester Composites For Mechanical And Tribological Applications
由: Nirmal, Umar
出版: (2011)

Creep characteristics of austenitic stainless steel foils under oxidative and non-oxidative environment
由: Mohammed Kadhim, Fatimah
出版: (2015)

Life cycle cost analysis of a floating production storage offloading vessel
由: Abu Hassan, Mohd. Akmal
出版: (2013)

Modeling lifetime warranty policy involving cost sharing between manufacturer and module supplier
由: Ranjbaran, Alireza
出版: (2013)

New And Improved Versions Of Genetic And PSO Algorithms For A Class Of Hybrid Systems And Steel Annealing Process
由: Arumugam, M. Senthil
出版: (2008)

Study of optimal machining parameters when machining AISI 304 stainless steel with carbide-pvd coated (TiAIN) cutting tool
由: Mohd Rahim, Mohd Yusri
出版: (2013)

Electrodeposition of carboxylated multiwall carbon nanotubes on graphite reinforcement carbon for voltammetry detection of cadmium
由: Othman, Nurul Farhana
出版: (2013)

Development and analysis of low-cost wearable servo valve using buckled tubes and embedded controller
由: Abdul Nasir, Abd Ghafar
出版: (2016)

Springback prediction in sheet metal forming: constitutive equations, finite element simulations and experimental validation
由: Jasri, Mohamad
出版: (2013)

A neural network approach for machine breakdown repair time
由: Chanthuru Thevendram,
出版: (2013)

Effect of Wire Electrical Discharge Machining (WEDM) parameters and additive treatment on surface roughness and dimensional stability of tool steel
由: Chew, Seow Lee
出版: (2013)

Effect of nitrogen pressure on Ti /TiA1 coating on 304 stainless steel by PVD-DC magnetron sputtering
由: Sabar, Mustafa Muneim
出版: (2013)

Investigation of surface metal matrix composites of reinforced aluminium alloy produced using friction stir processing
由: Che Dini Marini, Che Mohammad Ishkandar El-Rahimin
出版: (2020)

Investigation on mechanical properties of glass fiber reinforced polyamide 6-polypropylene composites under different operating conditions
由: Nurizzathanis, Mohamad Kusaseh
出版: (2020)

Experimental analysis and optimization of coated and uncoated carbide tool in drilling aisi 316 L austenite stainless steel using minimum quantity lubrication technique
由: Mukhtar, Malik
出版: (2018)

Defect analysis on investment casting: a case study
由: Sabudin, Sulastri
出版: (2004)

Physical behaviour of powder ceramic part using cold isostatic pressing (CIP) processes
由: Md. Ani, Sarizal
出版: (2006)

Study on iron and manganese removal in river water for textiles industry usage
由: Samad, Zaiton
出版: (2005)

Study on interoperability problems among CAD/CAM systems in automotive industry
由: Daniyal, Hamdan
出版: (2004)

Services hosted by the Perpustakaan Sultan Abdul Samad, Universiti Putra Malaysia with Cooperation MySyL Group