Effect of Fiber Orientation on Tensile Properties of Short Glass Fiber Reinforced Injection Molding Polypropylene Composite

The objective of this study is to examine the behaviour of composites and to provide an overview of short glass fiber reinforced injection-moulded theimoplastic, SgFRIMT in relation to the fiber orientation direction. In this study, the relationship between the mechanical propesties of samples co...

全面介绍

Saved in:
书目详细资料
主要作者: Ya'acob, Abdul Malek
格式: Thesis
语言:English
English
出版: 2004
主题:
在线阅读:http://psasir.upm.edu.my/id/eprint/6792/1/ITMA_2004_1.pdf
标签: 添加标签
没有标签, 成为第一个标记此记录!
id my-upm-ir.6792
record_format uketd_dc
spelling my-upm-ir.67922023-11-14T01:27:53Z Effect of Fiber Orientation on Tensile Properties of Short Glass Fiber Reinforced Injection Molding Polypropylene Composite 2004-05 Ya'acob, Abdul Malek The objective of this study is to examine the behaviour of composites and to provide an overview of short glass fiber reinforced injection-moulded theimoplastic, SgFRIMT in relation to the fiber orientation direction. In this study, the relationship between the mechanical propesties of samples containing longitudinal and transverse direction was studied in terms of the effects of injection speed, fiber concentration and fiber length on the mechanical properties of SgFRIMT. The orientation of fiber distribution in longitudinal and transverse direction was measured according to the gate position and samples- taken from identified position were investigated and tested at an angle relative to the fiber direction. The composite consisting of 5, 10, 15% wt of glass fiber was prepared using single screw extsuder model Brabender Plasticoder PL 2000, a compression molding machine and an 80-tonne Toshiba injection molding machine. The tensile properties were evaluated by Instron testing machine model 4301. The discussion focuses on the effects of fiber concentration, injecting speed and fiber length on tensile properties of a SgFRIMT. Tensile strength shows a steady decrease with increasing percentage of fiber loadings. In contrast, the tensile modulus increases significantly with an increase in the fiber loadings. At higher fiber concentration, the values of the modulus were higher than those of the unfilled polypropylene. The fiber breakage that occurs during sample preparation reduces the overall tensile strength significantly. Additional investigation was carried out on the effect of fiber breakage using 6 and 12 mm fiber length, where it was obsesved that the fiber breakage occurs during compounding stages with approximately 80% reduction in initial fiber length. Observation on the extrudates reveals that poor fiber matrix interaction causes the failure of the prepared samples. The presence of void and the agglomeration inside the samples considerably affects the mechanical properties of the composites. The results indicate that the stiffness and toughness of the SgFRIMT generally are influenced by the addition of glass fibers. In this study the influence of the injection speed was insignificant. The results of average fiber length agree with the results of other previous studies on SgFRIMT materials, indicating that the fiber length has major influence on the tensile properties of the prepased samples. Glass fibers 2004-05 Thesis http://psasir.upm.edu.my/id/eprint/6792/ http://psasir.upm.edu.my/id/eprint/6792/1/ITMA_2004_1.pdf text en public masters Universiti Putra Malaysia Glass fibers Institute of Advanced Technology Ahmad, Mansor English
institution Universiti Putra Malaysia
collection PSAS Institutional Repository
language English
English
advisor Ahmad, Mansor
topic Glass fibers


spellingShingle Glass fibers


Ya'acob, Abdul Malek
Effect of Fiber Orientation on Tensile Properties of Short Glass Fiber Reinforced Injection Molding Polypropylene Composite
description The objective of this study is to examine the behaviour of composites and to provide an overview of short glass fiber reinforced injection-moulded theimoplastic, SgFRIMT in relation to the fiber orientation direction. In this study, the relationship between the mechanical propesties of samples containing longitudinal and transverse direction was studied in terms of the effects of injection speed, fiber concentration and fiber length on the mechanical properties of SgFRIMT. The orientation of fiber distribution in longitudinal and transverse direction was measured according to the gate position and samples- taken from identified position were investigated and tested at an angle relative to the fiber direction. The composite consisting of 5, 10, 15% wt of glass fiber was prepared using single screw extsuder model Brabender Plasticoder PL 2000, a compression molding machine and an 80-tonne Toshiba injection molding machine. The tensile properties were evaluated by Instron testing machine model 4301. The discussion focuses on the effects of fiber concentration, injecting speed and fiber length on tensile properties of a SgFRIMT. Tensile strength shows a steady decrease with increasing percentage of fiber loadings. In contrast, the tensile modulus increases significantly with an increase in the fiber loadings. At higher fiber concentration, the values of the modulus were higher than those of the unfilled polypropylene. The fiber breakage that occurs during sample preparation reduces the overall tensile strength significantly. Additional investigation was carried out on the effect of fiber breakage using 6 and 12 mm fiber length, where it was obsesved that the fiber breakage occurs during compounding stages with approximately 80% reduction in initial fiber length. Observation on the extrudates reveals that poor fiber matrix interaction causes the failure of the prepared samples. The presence of void and the agglomeration inside the samples considerably affects the mechanical properties of the composites. The results indicate that the stiffness and toughness of the SgFRIMT generally are influenced by the addition of glass fibers. In this study the influence of the injection speed was insignificant. The results of average fiber length agree with the results of other previous studies on SgFRIMT materials, indicating that the fiber length has major influence on the tensile properties of the prepased samples.
format Thesis
qualification_level Master's degree
author Ya'acob, Abdul Malek
author_facet Ya'acob, Abdul Malek
author_sort Ya'acob, Abdul Malek
title Effect of Fiber Orientation on Tensile Properties of Short Glass Fiber Reinforced Injection Molding Polypropylene Composite
title_short Effect of Fiber Orientation on Tensile Properties of Short Glass Fiber Reinforced Injection Molding Polypropylene Composite
title_full Effect of Fiber Orientation on Tensile Properties of Short Glass Fiber Reinforced Injection Molding Polypropylene Composite
title_fullStr Effect of Fiber Orientation on Tensile Properties of Short Glass Fiber Reinforced Injection Molding Polypropylene Composite
title_full_unstemmed Effect of Fiber Orientation on Tensile Properties of Short Glass Fiber Reinforced Injection Molding Polypropylene Composite
title_sort effect of fiber orientation on tensile properties of short glass fiber reinforced injection molding polypropylene composite
granting_institution Universiti Putra Malaysia
granting_department Institute of Advanced Technology
publishDate 2004
url http://psasir.upm.edu.my/id/eprint/6792/1/ITMA_2004_1.pdf
_version_ 1794018686852399104