Experimental and simulation study on the effect of geometrical and flow parameters for combined-hole film cooling
Film cooling method was applied to the turbine blades to provide thermal protection from high turbine inlet temperatures in modern gas turbines. Recent literature discovers that combining two cylindrical holes of film cooling is one of the ways to further enhance the film cooling performances....
Saved in:
主要作者: | |
---|---|
格式: | Thesis |
語言: | English English English |
出版: |
2016
|
主題: | |
在線閱讀: | http://eprints.uthm.edu.my/751/1/24p%20HASWIRA%20HASSAN.pdf http://eprints.uthm.edu.my/751/2/HASWIRA%20HASSAN%20COPYRIGHT%20DECLARATION.pdf http://eprints.uthm.edu.my/751/3/HASWIRA%20HASSAN%20WATERMARK.pdf |
標簽: |
添加標簽
沒有標簽, 成為第一個標記此記錄!
|
id |
my-uthm-ep.751 |
---|---|
record_format |
uketd_dc |
spelling |
my-uthm-ep.7512021-08-30T07:49:40Z Experimental and simulation study on the effect of geometrical and flow parameters for combined-hole film cooling 2016-08 Hassan, Haswira TJ751-805 Miscellaneous motors and engines Including gas, gasoline, diesel engines Film cooling method was applied to the turbine blades to provide thermal protection from high turbine inlet temperatures in modern gas turbines. Recent literature discovers that combining two cylindrical holes of film cooling is one of the ways to further enhance the film cooling performances. In the present study, a batch of simulations and experiments involving two cylindrical holes with opposite compound angle were carried out and this two cylindrical hole also known as combined-hole film cooling. The main objective of this study is to determine the influence of different blowing ratio, M with a combination of different lateral distance between cooling holes (PoD), a streamwise distance between cooling holes (LoD) and compound angle of cooling hole (1/2) on the film cooling performance. The simulation of the present study had been carried out by using Computational Fluid Dynamic (CFD) with application of Shear Stress Transport (SST) turbulence model analysis from ANSYS CFX. Meanwhile, the experimental approach makes used of open end wind tunnel and the temperature distributions were measured by using infrared thermography camera. The purpose of the experimental approach in the present study is to validate three cases from all cases considered in the simulation approach. As the results shown, the lateral coverage was observed to be increased as PoD and 1/2 increased due to the interaction between two cooling air ejected from both cooling holes. Meanwhile, film cooling performance insignificantly changed when different LoD was applied. As the conclusion, a combination of the different geometrical parameters with various flow parameters produced a pattern of results. Therefore, the best configuration has been determined based on the average area of film cooling effectiveness. For M = 0.5, PoD = 1.0, LoD = 2.5 and 1 / 2 = -45o /+45o case is the most effective configuration. In the case of M = 1.0 and M = 1.5, PoD = 0.0, LoD = 3.5, 1 / 2 = -45o /+45o and PoD = 0.0, LoD = 2.5, 1 / 2 = -45o /+30o are the best configurations based on the overall performance of film cooling. 2016-08 Thesis http://eprints.uthm.edu.my/751/ http://eprints.uthm.edu.my/751/1/24p%20HASWIRA%20HASSAN.pdf text en public http://eprints.uthm.edu.my/751/2/HASWIRA%20HASSAN%20COPYRIGHT%20DECLARATION.pdf text en staffonly http://eprints.uthm.edu.my/751/3/HASWIRA%20HASSAN%20WATERMARK.pdf text en validuser mphil masters Universiti Tun Hussein Onn Malaysia Fakulti Kejuruteraan Mekanikal dan Pembuatan |
institution |
Universiti Tun Hussein Onn Malaysia |
collection |
UTHM Institutional Repository |
language |
English English English |
topic |
TJ751-805 Miscellaneous motors and engines Including gas gasoline diesel engines |
spellingShingle |
TJ751-805 Miscellaneous motors and engines Including gas gasoline diesel engines Hassan, Haswira Experimental and simulation study on the effect of geometrical and flow parameters for combined-hole film cooling |
description |
Film cooling method was applied to the turbine blades to provide thermal protection
from high turbine inlet temperatures in modern gas turbines. Recent literature
discovers that combining two cylindrical holes of film cooling is one of the ways to
further enhance the film cooling performances. In the present study, a batch of
simulations and experiments involving two cylindrical holes with opposite compound
angle were carried out and this two cylindrical hole also known as combined-hole film
cooling. The main objective of this study is to determine the influence of different
blowing ratio, M with a combination of different lateral distance between cooling holes
(PoD), a streamwise distance between cooling holes (LoD) and compound angle of
cooling hole (1/2) on the film cooling performance. The simulation of the present
study had been carried out by using Computational Fluid Dynamic (CFD) with
application of Shear Stress Transport (SST) turbulence model analysis from ANSYS
CFX. Meanwhile, the experimental approach makes used of open end wind tunnel and
the temperature distributions were measured by using infrared thermography camera.
The purpose of the experimental approach in the present study is to validate three cases
from all cases considered in the simulation approach. As the results shown, the lateral
coverage was observed to be increased as PoD and 1/2 increased due to the interaction
between two cooling air ejected from both cooling holes. Meanwhile, film cooling
performance insignificantly changed when different LoD was applied. As the
conclusion, a combination of the different geometrical parameters with various flow
parameters produced a pattern of results. Therefore, the best configuration has been
determined based on the average area of film cooling effectiveness. For M = 0.5, PoD
= 1.0, LoD = 2.5 and 1 / 2 = -45o
/+45o
case is the most effective configuration. In the
case of M = 1.0 and M = 1.5, PoD = 0.0, LoD = 3.5, 1 / 2 = -45o
/+45o
and PoD = 0.0,
LoD = 2.5, 1 / 2 = -45o
/+30o
are the best configurations based on the overall
performance of film cooling. |
format |
Thesis |
qualification_name |
Master of Philosophy (M.Phil.) |
qualification_level |
Master's degree |
author |
Hassan, Haswira |
author_facet |
Hassan, Haswira |
author_sort |
Hassan, Haswira |
title |
Experimental and simulation study on the effect of geometrical and flow parameters for combined-hole film cooling |
title_short |
Experimental and simulation study on the effect of geometrical and flow parameters for combined-hole film cooling |
title_full |
Experimental and simulation study on the effect of geometrical and flow parameters for combined-hole film cooling |
title_fullStr |
Experimental and simulation study on the effect of geometrical and flow parameters for combined-hole film cooling |
title_full_unstemmed |
Experimental and simulation study on the effect of geometrical and flow parameters for combined-hole film cooling |
title_sort |
experimental and simulation study on the effect of geometrical and flow parameters for combined-hole film cooling |
granting_institution |
Universiti Tun Hussein Onn Malaysia |
granting_department |
Fakulti Kejuruteraan Mekanikal dan Pembuatan |
publishDate |
2016 |
url |
http://eprints.uthm.edu.my/751/1/24p%20HASWIRA%20HASSAN.pdf http://eprints.uthm.edu.my/751/2/HASWIRA%20HASSAN%20COPYRIGHT%20DECLARATION.pdf http://eprints.uthm.edu.my/751/3/HASWIRA%20HASSAN%20WATERMARK.pdf |
_version_ |
1747830674091409408 |