Performance evaluation of wiper and conventional coated ceramic inserts when turning hardened tool steel

Performance evaluation of wiper and conventional coated ceramic inserts when turning hardened tool steel

Saved in:

書目詳細資料
主要作者:	Affandi Mohd. Zainal, Affandi
格式:	Thesis
出版:	2006
主題:	Unspecified
標簽:	添加標簽沒有標簽, 成為第一個標記此記錄!

相似書籍

Wear mechanism and surface integrity studies when turning hardened tool steel using wiper coated ceramic tool
由: Umar, Alkali Adam
出版: (2011)

Performance evaluation of wiper coated ceramic tool when hard turning tool steel
由: Saad Elmunafi, Mohamed Handawi
出版: (2010)

Performance evaluation of ceramic and PCBN cutting tools when turning hardened steel
由: Abd. Jamil, Saiful Bahri
出版: (2004)

Performance evaluation of coated ceramic cutting tools with T-land edge preparation when turning hardened tool steel
由: Wan Abdul Rahaman, Wan Emri
出版: (2006)

Performance evaluation of coated carbide and coated cermet tools when turning hardened tool steel
由: Mohd. Yusof, Noordin
出版: (2003)

Performance evaluation of coated carbide and coated cermet tools when turning hardened tool steel
由: Mohd. Yusof, Noordin
出版: (2004)

Performance evaluation of coated carbide cutting tools when turning hardened tool steel
由: Tang, Yu Cai
出版: (2006)

Performance evaluation of different edge geometry when turning hardened DF3 tool steel
由: Davoudinejad, Ali
出版: (2012)

Tool life and surface integrity when hard turning stainless steel using wiper coated carbide tool
由: Kurniawan, Denni
出版: (2008)

Performance of cubic boron nitride and mixed ceramics tools when hard turning tool steel
由: Mohamad, Ahmad Kamely
出版: (2008)

Evaluation of ceramic cutting tool performance when turning tool steels
由: Konneh, Mohamed
出版: (1998)

Performance of coolant strategies when turning hardened martensitic stainless steel using tialn coated carbide tool
由: Mohamed Elshwaini, Amad Elddein Issa
出版: (2017)

Experimental study on hard turning of hardened tool steel with coated carbide cutting tools
由: K. Seveen, K. Muniswaran
出版: (2007)

Tool wear and tool life performance of TiA1N coated carbide cutting tools when turning XW 42 hardened tool steel
由: Effendy, Effendy
出版: (2007)

Machinability assessment when turning AISI 316L austenitic stainless steel using uncoated and coated carbide inserts
由: Nur, Rusdi
出版: (2016)

Effect of edge preparation when hard turning tool steel
由: Shaari, Mohd. Rosmani
出版: (2010)

Performance and evaluation of graphite when machining hardened steel ASSAB 718
由: Saeed Ahmed, Radwan Ahmed
出版: (2009)

Performance of whisker reinforced ceramic insert during hard turning
由: Balakrishnan, Santhirakumar
出版: (2003)

Developement of ceramic cutting insert of alumina (Al2O3) and zirconia / zirconium oxide (ZrO2) for turning tool steel
由: Shamsudin, Zuraidy
出版: (2007)

cutting performance and wear of ZTA-TiO2-Cr03 mixed ceramic cutting tools when turning stainless steel 316L
由: Raqibah Najwa Binti Mudzaffar

Optimization of cuting parameters for ceramic tool having different edge geometries in hard turning of tool steel /
由: Rohaizad Jamaludin
出版: (2015)

Effect of silicon morphology on various machinability parameters when turning A1-Si-Cu-Mg alloy
由: Barzani, Mohsen Marani
出版: (2012)

Modeling of reactively sputtered TiAIN coating on tungsten carbide insert tool its properties and cutting performance in dry turning of AISI D2 steel
由: Budi, Esmar
出版: (2010)

Performance evaluation of powder metallurgy tool electrodes in electrical discharge machining of hardened steel /
由: Nik Masmiati Nik Pa
出版: (2006)

A study of ceramic tool fracture in interrupted turning /
由: Husni
出版: (2010)

Performance of PCBN inserts and ceramic inserts
由: Ngu, Ching Kui
出版: (2002)

Performance evaluation of uncoated and coated carbide tools when drilling titanium alloy
由: Abd. Rahim, Erween
出版: (2005)

Performance evaluation of uncoated and coated carbide tools when drilling titanium alloy
由: Abd. Rahim, Erween
出版: (2005)

Modelling of stagnant zone formation on diamond cutting tool when turning titanium alloy
由: Thet, Thet Mon
出版: (2007)

Surface Integrity And Tool Wear Of Hardened HTCS-150 Steel (52 HRC) In Milling With Tia1n Coated Carbide
由: Azhar, Anis Afuza
出版: (2019)

Experimental investigations of cutting parameters influence on cutting forces, surface roughness and tool life when finish hard turning of Stavax ESR steel
由: Adamu, Gidado Bashir
出版: (2013)

Analyses of tool life and surface roughness during hard turning of AISI H13 hot work tool steel using mixed ceramic tools
由: Tan, Poh Lai
出版: (2003)

A study of laser transformation hardened DF2 tool steel specimens /
由: Yang, Lin Jiang
出版: (1993)

Performance evaluation of different process conditions when hard turning ASSAB 760
由: Azman, Azri
出版: (2010)

Detection Of Chipping In Ceramic Cutting Inserts From Workpiece Profile Signature During Turning Process Using Machine Vision
由: Kiow, Lee Woon
出版: (2017)

Detection Of Chipping In Ceramic Cutting Inserts From Workpiece Profile Signature During Turning Process Using Machine Vision
由: Lee, Woon Kiow
出版: (2017)

Effect of vegetable and mineral oil-in-water emulsion cutting fluids in turning AISI 4340 steel with coated carbide tools /
由: Lawal, Sunday Albert
出版: (2013)

Study of optimal machining parameters when machining AISI 304 stainless steel with carbide-pvd coated (TiAIN) cutting tool
由: Mohd Rahim, Mohd Yusri
出版: (2013)

Wiper Protection / Mohammad Nazir Marzuki
由: Marzuki, Mohammad Nazir
出版: (2007)

Machinability study of uncoated and coated carbide tools when drilling CFRP/metal stacks
由: Mahamad Hakimi, Ismail
出版: (2015)

Services hosted by the Perpustakaan Sultan Abdul Samad, Universiti Putra Malaysia with Cooperation MySyL Group