Parameter analysis on wire-cut EDM process of silicon carbide

Parameter analysis on wire-cut EDM process of silicon carbide

Saved in:

Bibliographic Details
Main Author:	Abdul Rahim, Muhammad Khairi
Format:	Thesis
Published:	2013
Subjects:	TK Electrical engineering Electronics Nuclear engineering
Tags:	Add Tag No Tags, Be the first to tag this record!

Similar Items

Parameter analysis on wire-cut EDM process of silicon carbide
by: Rahim, Mohammad Zulafif
Published: (2011)

Analysis of non uniform surface current distribution on thick and thin wire antenna
by: Abd. Rahman, Rais Rabani
Published: (2013)

Effect of heat treatments on silicon dioxide and silicon nitride nanocomposites
by: Ahmad Ritzzney, Muhammad Isamuddin
Published: (2019)

Study on machining parameters optimization in EDM of tungsten carbide using the Taguchi method
by: Lajis, Mohd. Amri
Published: (2002)

Statistical approach in solving for initial and eventual wire bonding problem
by: Somasundram, Suresh Kumar
Published: (2013)

Classification of wire bonding machine signatures using fuzzy logic
by: Daud, Zaimah
Published: (2001)

Analysis of electrochemical parameters for activated carbon supercapacitor
by: Azidzul, Muhammad Aiman
Published: (2020)

E-NSGA-II for machining process parameters optimization
by: Yusoff, Yusliza
Published: (2012)

Fault detection and isolation using sliding mode observer for steer-by-wire
by: Kheirandish, Azadeh
Published: (2010)

Deposition And Characterisation Of Solution Processed Indium Gallium Zinc Oxide Thin Film On Silicon Substrate
by: Kasim, Nabihah
Published: (2022)

Design and analysis of the silicon-based integrated metal-insulator-metal capacitor
by: Rosli, Nurul Asyikin
Published: (2022)

A conceptual design of an alternative method for cutting off standby power consumption for office equipment
by: Tan, Kheng Wee
Published: (2012)

Analysis of non uniform surface current distribution on thick and thin wire antenna
by: Abd. Rahman, Rais Rabani
Published: (2013)

Study Of The Relationship Between Delta Delay And Adjacent Parallel Wire Length In 45 Nanometer Process Technology
by: Mohamed, Shamsul Anuar
Published: (2014)

Stress effect on bond pad and fab of gold and copper wires / Nik Muhammad Fareez Wan Shah
by: Wan Shah, Nik Muhammad Fareez
Published: (2013)

Analysis Of Plastic Encapsulation Process In 3D IC Package With Through-Silicon Via (Tsv) Technology
by: Ong, Ern Seang
Published: (2013)

Silicon nanowire arrays for thermoelectric power harvesting
by: Abdul Tahrim, 'Aqilah
Published: (2018)

The effect of sample processing parameters on breakdown properties of polyethylene and polypropylene blends
by: Ismail, Nor Hashimah
Published: (2020)

Modeling and analysis of cylindrical gate-all around silicon nanowire FET including BOHM quantum potential model
by: Abd. Razak, Muhammad A’tif
Published: (2018)

Generation of homogeneous glow discharge using a combination of fine wire mesh perforated aluminium alectrode
by: Sahari, Norain
Published: (2013)

Proportional-integral-derivative control algorithm with delay compensation for steer-by-wire under network controlled system
by: Zainal, Mohd. Sazlan
Published: (2015)

Effect Of Carbon Additives And Surfactant On Electrical Discharge Machining (EDM) Of Reaction-Bonded Silicon Carbide (RB-SiC)
by: Abdul Razak, Muhammad Raziman
Published: (2017)

Analysis of modulation parameters of high frequency digital modulation signal
by: Anuar, Hardy Azmir
Published: (2004)

Surface acoustic wave gas sensor with nanostructured silicon sensing element
by: Ahmad Asri, Muhammad Izzudin
Published: (2022)

Investigation of silicon nitride capping layer and embedded silicon germanium effect on 90 nm CMOS devices / Norlina Mohd Zain
by: Mohd Zain, Norlina
Published: (2010)

Development and fabrication of ignitor circuit for portable laser cutting machine / Rohayu Muhamad Zain
by: Muhamad Zain, Rohayu
Published: (1998)

Pengoptimuman parameter-parameter transducer akustik elektromagnet (EMAT) untuk pengukuran ultrasonik
by: Abdul Hamid, Siti Noorjannah
Published: (1996)

Shielding effectiveness of mesh wire for 50Hz magnetic field
by: El-Shami, Ibtihal Fawzi
Published: (2011)

Performance evaluation of uncoated and coated carbide tools when end milling of titanium alloy using response surface methodology
by: Mohruni, Amrifan Saladin
Published: (2008)

P-type silicon nanowire transistor modeling and simulation
by: Fallahpour, Amir Hossein
Published: (2009)

Identification of synchronous machine parameters
by: Abdul Majid, Nor'aini
Published: (1989)

Effect of water on breakdown characteristics of polyethylene/silicon nitride nanocomposites
by: Mohd. Zafrullah, Siti Nur Rahmah
Published: (2017)

Electrochemically deposited germanium on silicon and its crystallization by rapid melting growth
by: Zainal Abidin, Mastura Shafinaz
Published: (2014)

Electrical treeing performance of silicone rubber filled with plasma-treated nanoparticles
by: Musa, Fatin Nabilah
Published: (2016)

Sensitivity study on influencing parameters of transformer thermal model with directed oil flow
by: Nik Supian, Nik Mohd Azri
Published: (2013)

Electrical and temperature characterisation of silicon and germanium nanowire transistors based on channel dimensions
by: Hani Taha, Abd Assamad Al Ariqi
Published: (2020)

Arithmetic logic unit design for silicon nanowire field-effect transistors logic
by: Mohd. Munir Zahari, Nor Hafizah
Published: (2015)

Fabrication and characterization of reduced graphene oxide/silicon back-to-back schottky diode
by: Che Azmi, Siti Nadiah
Published: (2018)

Effect of filler on self-healing properties of silicone rubber in electrical tree phenomena
by: Zakaria, Izzah Hazirah
Published: (2015)

Propose of the lens system as a part in development of optical system for Red Ruby Laser Material Cutting Tools / Norazmi Bakar
by: Bakar, Norazmi
Published: (1998)

Services hosted by the Perpustakaan Sultan Abdul Samad, Universiti Putra Malaysia with Cooperation MySyL Group