Performance of whisker reinforced ceramic insert during hard turning

Performance of whisker reinforced ceramic insert during hard turning

Saved in:

书目详细资料
主要作者:	Balakrishnan, Santhirakumar
格式:	Thesis
出版:	2003
主题:	T Technology (General) TJ Mechanical engineering and machinery
标签:	添加标签没有标签, 成为第一个标记此记录!

相似书籍

Performance of PCBN inserts and ceramic inserts
由: Ngu, Ching Kui
出版: (2002)

Performance evaluation of wiper coated ceramic tool when hard turning tool steel
由: Saad Elmunafi, Mohamed Handawi
出版: (2010)

Detection Of Chipping In Ceramic Cutting Inserts From Workpiece Profile Signature During Turning Process Using Machine Vision
由: Lee, Woon Kiow
出版: (2017)

Performance of carbide insert in turning of titanium alloy under carbon dioxide cryogenic cooling
由: Mat, Siti Asiyah
出版: (2021)

Detection Of Chipping In Ceramic Cutting Inserts From Workpiece Profile Signature During Turning Process Using Machine Vision
由: Kiow, Lee Woon
出版: (2017)

Surface roughness analysis on titanium alloy Ti-6AI-4V ELI during turning with uncoated carbide insert
由: Mastuki, Ammar Aizat
出版: (2019)

Performance of minimum quantity lubrication using paraffin based nanofluids during hard turning of AISI420 stainless steel
由: Majeed, Faraj Saeid Adrees
出版: (2022)

Effect of edge preparation when hard turning tool steel
由: Shaari, Mohd. Rosmani
出版: (2010)

Evaluation of ceramic cutting tool performance when turning tool steels
由: Konneh, Mohamed
出版: (1998)

Performance evaluation of ceramic and PCBN cutting tools when turning hardened steel
由: Abd. Jamil, Saiful Bahri
出版: (2004)

Effect of environmental condition and nickel underlayer on whiskers formation in tin surface finish
由: Yusof, Siti Zahira
出版: (2014)

Developement of ceramic cutting insert of alumina (Al2O3) and zirconia / zirconium oxide (ZrO2) for turning tool steel
由: Shamsudin, Zuraidy
出版: (2007)

Performance evaluation of different process conditions when hard turning ASSAB 760
由: Azman, Azri
出版: (2010)

Experimental study on hard turning of hardened tool steel with coated carbide cutting tools
由: K. Seveen, K. Muniswaran
出版: (2007)

Investigation on Hardness and Corrosion Properties of Graphene Nanoplatelets Reinforced Magnesium Composite
由: Abang Mohamad Harith, Beniamin
出版: (2023)

Machinability assessment when turning AISI 316L austenitic stainless steel using uncoated and coated carbide inserts
由: Nur, Rusdi
出版: (2016)

Performance evaluation of coated ceramic cutting tools with T-land edge preparation when turning hardened tool steel
由: Wan Abdul Rahaman, Wan Emri
出版: (2006)

Tool life and surface integrity when hard turning stainless steel using wiper coated carbide tool
由: Kurniawan, Denni
出版: (2008)

Performance of Minimum Quantity Lubrication System with Vegetable Oils in Turning
由: Teo, Chong Yaw
出版: (2017)

Experimental investigations of cutting parameters influence on cutting forces, surface roughness and tool life when finish hard turning of Stavax ESR steel
由: Adamu, Gidado Bashir
出版: (2013)

Development of ceramic cutting insert of aluminium oxide (Al2O3) and titanium carbide (TiC) for machining steel
由: Isa, Mohd. Akmal
出版: (2007)

Surface roughness study on aluminium in high speed turning process
由: Dahlan, Mohd Shazwan
出版: (2019)

Analyzing the effect of parameter setting on surface roughness of turning process
由: Alias, Mohd Fairuz
出版: (2022)

Performance evaluation of ultrasonic assisted wire electrical discharge turning for TI-6AL-4V material
由: Mohd Zakaria, Muhammad Akmal
出版: (2023)

Prediction Of Tool Wear Characteristics In Turning On Inconel 718 : Experimentation And Simulation
由: Abd Aziz, Syazxerlin
出版: (2018)

Surface roughness study on mild steel in high speed turning process
由: Muhammad Kamal Aysraf, Pubin
出版: (2016)

The effect of cryogenic carbon dioxide cooling on surface integrity of titanium alloy in turning
由: Razak, Muhammad Shahmi
出版: (2021)

Effect of machining parameters and bismuth addition on al-20%mg2si machinability during dry turning
由: Razavykia, Abbas
出版: (2014)

Fabricate And Investigate The Performance Of Alumina Based Ceramic Cutting Tool With Different Edge
由: Mat Amin, Mohd Imran
出版: (2018)

Surface Roughness Study On Mild Steel In Conventional Turning Process Under Three Condition Cutting Fluids
由: Abdullah, Abd Halimnizam
出版: (2019)

Performance evaluation of coated carbide cutting tools when turning hardened tool steel
由: Tang, Yu Cai
出版: (2006)

The Effect Of Synthetic Soluble Cutting Fluid Pressure Towards Machinability Using Stainless Steel 304 With Coated Cemented Carbide Insert
由: Zainal Ariffin, Selamat
出版: (2009)

Effect of tool length on plain turning performance
由: Ibrahim, Norfaizem
出版: (2010)

Performance evaluation of coated carbide and coated cermet tools when turning hardened tool steel
由: Mohd. Yusof, Noordin
出版: (2003)

Performance evaluation of coated carbide and coated cermet tools when turning hardened tool steel
由: Mohd. Yusof, Noordin
出版: (2004)

Experimental analysis of machining performance based on selected cutting parameters for smart CNC turning environment
由: Mohamad, Shuhaidi
出版: (2014)

Pressure gradient and geometrical variation of the abrasive blocks during the polishing process of ceramic tiles with line contact
由: Amiril Sahab, Abdul Sani
出版: (2014)

Study on defect of aluminium filled epoxy mold insert in injection molding
由: Abd. Rahim, Saiful Azril
出版: (2013)

Forced convection heat transfer performance of TiO2-SiO2 nanofluids with wire coil inserts
由: Khamisah, Abdul Hamid
出版: (2019)

Performance of coolant strategies when turning hardened martensitic stainless steel using tialn coated carbide tool
由: Mohamed Elshwaini, Amad Elddein Issa
出版: (2017)

Services hosted by the Perpustakaan Sultan Abdul Samad, Universiti Putra Malaysia with Cooperation MySyL Group