Investigation into minimal cutting fluid application in high speed milling of hardened steel using carbide mills /

Investigation into minimal cutting fluid application in high speed milling of hardened steel using carbide mills /

Saved in:

书目详细资料
主要作者:	Thanongsak Thepsonthi
格式:	Thesis 图书
语言:	English
出版:	2005.
主题:	Metal-working lubricants. Metal-cutting. Milling (Metal-work)
标签:	添加标签没有标签, 成为第一个标记此记录!

相似书籍

The effect of lubricant entrainment direction on high speed milling of stainless steel /
由: Natasha A. Raof
出版: (2011)

Effect of vegetable and mineral oil-in-water emulsion cutting fluids in turning AISI 4340 steel with coated carbide tools /
由: Lawal, Sunday Albert
出版: (2013)

Effect of backcutting on surface roughness during high speed end milling /
由: Afifah binti Mohd. Ali
出版: (2012)

Development of an integrated and control system for minimal quantity lubricant application /
由: Izatul Nadia Mohd Yassin
出版: (2012)

Optimisation of wire electrical discharge machining process using XW41 tool steel material /
由: Mohanadhas Kanagaraj
出版: (2011)

Optimisation of wire electrical discharge machining process using DF2 tool steel material /
由: Cheah, Aik Keong
出版: (2011)

Effect of rotational electrode on : the performance of EDM milling /
由: Iqbal, Asif
出版: (2010)

Tool path cutting strategy for milling aircraft components using aluminium 7050
由: Alsultaney, Hazem K.
出版: (2010)

A new cost model for high speed hard turning of AISI 4340 steel /
由: al-Hazza, Muataz Hazza Faizi
出版: (2012)

Performance evaluation of electrical discharge machining using cerium oxides nanofluid and multi-metal oxide as powder mixed dielectrical fluid /
由: Hossain, Md Moktar
出版: (2020)

Preheated machining of AISI D2 hardened steel and optimization of parameters /
由: Mohd Amri bin Lajis
出版: (2010)

Effect of vibrated workpiece in electrical discharge machining (EDM) /
由: Gunawan Setia Prihandana
出版: (2006)

Optimization of cutting conditions on tool life in face milling spheroidal graphite cast iron using Taguchi method
由: Bahurdin, Mohamad Maaroff
出版: (2012)

Performance evaluation of powder metallurgy tool electrodes in electrical discharge machining of hardened steel /
由: Nik Masmiati Nik Pa
出版: (2006)

Diamond particle distributed in cemented carbide /
由: Authayarat, Waratta
出版: (2007)

Relationship of chip load and spindle speed on cutting force and surface integrity for high-speed dry end-milling Hastelloy X material
由: Mohd Nor, Nor Aznan
出版: (2019)

A novel process for increasing deep drawability of rectangular metal cups with extreme aspect ratio : design and simulation /
由: Jafarlou, Davoud Mashhadi
出版: (2013)

Study of sheet metal cutting using low power carbon dioxide laser machine /
由: Chandrasekariah, Sastry
出版: (2001)

The Evaluation of Machinability and Surface Texture of Tool Steel with Copper Electrode in Electro Discharge Machining
由: Mohd Daud, Mohd Ahadlin
出版: (2001)

Heat distribution of magnesium alloys (AZ31B) on electro discharge machining using finite element analysis /
由: Muhammad Izzuddin Zakaria
出版: (2018)

Finite element simulation and experimental verification of temper rolling process of low carbon steel sheet /
由: Azhar Abdul Satar
出版: (2013)

Plasma cladding of titanium carbide on steel /
由: Mohd Shahriman Adenan
出版: (2007)

Machinability assessment and enhancement of aerospace alloys through workpiece preheating in end milling /
由: Hossain, Mohammad Istiyaq
出版: (2008)

Chatter & machinability aspects in end milling of metal matrix composite (MMC) and titanium alloys -Ti-6A1-4V using carbide & pcd inserts /
由: Nor Khairusshima binti Muhamad Khairussaleh
出版: (2007)

Evaluation of coatings on cutting tool materials /
由: Lee, Chee Hueng
出版: (1992)

Optimization of electrical discharge machining process on mild steel workpiece with copper tools /
由: Tamjidy, Mehran
出版: (2012)

Study on the correlation between cutting force & tool wear in metal cutting /
由: Kyaw, Min Swe
出版: (1997)

A study of the consistency of tool wear characteristics and the criteria for onset of tool failure /
由: Neelakantan, Sudhar
出版: (1994)

Optimization of surface roughness using response surface methodology and genetic algorithm in high speed and milling of titanium alloy : Ti-6A1-4V /
由: Md. Shah Alam
出版: (2009)

Mapping the wear of cutting tool materials /
由: Lee, Soon Hing
出版: (1992)

Finite element analysis and experimental validation of incremental sheet metal analysis forming process /
由: Echrif, Salah Basheer M.
出版: (2014)

Investigate the effects of cutting parameters and lubrication modes on the tool deflection error in end milling of aluminum 6061 /
由: Nguyen, Trung Nghiep
出版: (2015)

Surface coatings for cutting tools /
由: Lim, Christina Yui Hung
出版: (1996)

Monitoring of tool wear in milling using cutting force sensing /
由: Ning, Ting
出版: (1997)

Fabrication and wear characteristics of alumina tools /
由: Goh, Gregory Kia Liang
出版: (1995)

Micro-finishing of EDM machined dies by abrasive jet machining /
由: Venkataraman Narayanan
出版: (1987)

Performance of cermet tools with negative rake angles during high speed machining /
由: Muhammad Riza
出版: (2010)

Neural networks prediction of cutting tool wear during turning operations /
由: Mahardika, Muslim
出版: (2005)

A study of surface hardening using robotic plasma arc /
由: Mohd Idris Shah Ismail
出版: (2007)

Effect of flushing pressure on electro-discharge machining and resultant surface characteristics /
由: Wang, Yun Kang
出版: (1994)

Services hosted by the Perpustakaan Sultan Abdul Samad, Universiti Putra Malaysia with Cooperation MySyL Group