Effects of online workpiece preheating on the machinability of hardened steel AISI H13 during end milling and development of prediction models using RSM /

Effects of online workpiece preheating on the machinability of hardened steel AISI H13 during end milling and development of prediction models using RSM /

Saved in:

書目詳細資料
主要作者:	Abdullah Mohammad Khalid Hafiz
格式:	Thesis
語言:	English
出版:	Gombak, Selangor : Kulliyyah of Engineering, International Islamic University Malaysia, 2008
主題:	Hard materials > Machining Machining Theses, IIUM local
在線閱讀:	http://studentrepo.iium.edu.my/handle/123456789/4437
標簽:	添加標簽沒有標簽, 成為第一個標記此記錄!

相似書籍

Multi objective optimization of high speed end milling of AISI D2 using meta heuristic approach /
由: Seder, Amin M. F.
出版: (2016)

Cost models for comparing room temperature and preheated end-miling of AISI D2 tool steel /
由: Elhadie, Mohamed
出版: (2011)

Preheated machining of AISI D2 hardened steel and optimization of parameters /
由: Mohd Amri bin Lajis
出版: (2010)

Machinability assessment and enhancement of aerospace alloys through workpiece preheating in end milling /
由: Hossain, Mohammad Istiyaq
出版: (2008)

A new cost model for high speed hard turning of AISI 4340 steel /
由: al-Hazza, Muataz Hazza Faizi
出版: (2012)

End milling machinability of H13 tool steel using carbide and cements tools /
由: Jaharah A. Ghani
出版: (2005)

Performance evaluation of machine tool structures /
由: Chua, Kah Hock
出版: (1992)

Abrasive waterjet machining of composite ballistic materials (Kevlar) /
由: Rahmah Bte Abdullah
出版: (2005)

Generation, acquisition and analysis of machining data for aircraft materials and study of wear while machining these materials /
由: Jeyaseelan, Thomas
出版: (1985)

Material removal rate and surface roughness in electrical discharge machining of alumina /
由: Moudood, A.H.M. Abdul
出版: (2015)

Special machine design for sculpting foam materials in 3D /
由: Riza Sulaiman
出版: (2004)

An intelligent fault diagnosis system for machining /
由: Zhou, Qiang
出版: (1996)

A study on machining characteristics of strontium modifies LM-6 alloy /
由: Hajjaj, Sami Salama
出版: (2007)

Effects of chromium powder mixed in electrical discharge machining of AISI D2 hardened steels
由: Idris, Muhammad Ridzuan
出版: (2015)

Three dimensional cutting force and tool deflection in micro-end milling AISI D2 / Noor Aniza Norrdin
由: Norrdin, Noor Aniza
出版: (2016)

An integrated knowledge-based machining system for rotationally symmetric parts /
由: Yeo, Swee Hock
出版: (1992)

Improved machinability of titanium alloy TI-6AL-4V through workpiece preheating /
由: Ginta, Turnad Lenggo
出版: (2010)

Influence of agglomeration phenomenon in machining of AISI D2 hardened steel using nano chromium powder mixed-EDM
由: Abbas, Mohammed Abdulridha
出版: (2020)

CAD integrated machining cost estimation and optimisation /
由: Joseph, Ladislaus A.
出版: (1995)

Effect of chromium (cr) particle size and span-20 surfactant on Aisi d2 hardened steel using electrical discharge machining
由: Jamil Hosni, Nor Ain
出版: (2020)

Study of tool engagement and tool path strategy in high speed end milling /
由: Roshaliza Hamidon
出版: (2017)

Investigation of machining parameters on abrasive water jet machined surface of glass/epoxy composites using Taguchi method /
由: Mohd Azmir Mohd Azhari
出版: (2006)

Anggaran parameter pemesinan menggunakan kaedah algoritma genetik /
由: Suhaime Sapari
出版: (2005)

Investigation on different composition of powder metallurgy electrode (Cu-W) in high performance edm (HPEDM) on AISI D2 hardened steel
由: Abdul Hamid, Faizul Ezmat
出版: (2013)

Cutting performance of advanced multilayer coated (TiAlN/AlCrN) in machining of AISI D2 hardened steel
由: Jasni, Nur Akmal Hakim
出版: (2013)

Pemantauan haus mata alat berasaskan isyarat getaran dan bunyi melalui kaedah analisis Dekomposisi Frekuaensi Fibonacci Z /
由: Muhamad Arif Fadli Ahmad

Investigation of the causes of chatter in machine tools and development of a new chatter model /
由: Mohammed Anayet Ullah Patwari
出版: (2010)

Performance of laser assisted micro-milling (laμmill) of titanium alloy using micro ball end mill
由: Mohid, Zazuli
出版: (2018)

Surface roughness and tool wear aspects in heat assisted high speed ductile mode end milling of soda lime glass /
由: Noor Fathiah binti Mohd Zaib
出版: (2016)

A simulation of machining process using finite element method /
由: Fadly Jashi Darsivan
出版: (2002)

Tool condition monitoring for turning by acoustic emission /
由: Bi, Lin Ling
出版: (1996)

Finite element analysis of machining /
由: Prabhakaran, Sudheer

Machine tool failure analysis using image and signal processing techniques /
由: Ma, Jing
出版: (1998)

Evaluation of tool edge geometry for turning of assab DF-3 and aliminium using taguchi method /
由: Mohd Muhaymin Muhamad
出版: (2015)

Effect of tool path strategies on machining performance of AISI H13 during poketing in high speed end milling /
由: Muhammad Riza
出版: (2016)

Effect of backcutting on surface roughness during high speed end milling /
由: Afifah binti Mohd. Ali
出版: (2012)

Extraction and characterization of coagulation active agent from moringa oleifera for turbidity and hardness removal in raw water sources
由: Nurfahasdi, Meutia

Reverse engineering through 3D optical scanning: Cylinder head (4G13) & side mirror case study / Aizah Adrianee Mardzuki
由: Mardzuki, Aizah Adrianee
出版: (2005)

Performance analysis of thermal arc spray aluminium coating as a sacrificial anode / Muhamad Hafiz Abd Malek
由: Abd Malek, Muhamad Hafiz
出版: (2015)

Study on high performance dual-stage servomechanism in hard disk drives /
由: Wu, Daowei
出版: (2003)

Services hosted by the Perpustakaan Sultan Abdul Samad, Universiti Putra Malaysia with Cooperation MySyL Group